• SS&Si
  • Kidde Commercial
  • Kidde | 10 Amp Remote NAC Booster Power Supply with Battery Backup, UL 864 10th Edition | MIRBPS10A
10 Amp Remote NAC Booster Power Supply with Battery Backup, UL 864 10th Edition
Kidde Commercial

10 Amp Remote NAC Booster Power Supply with Battery Backup, UL 864 10th Edition

SKU KD-MIRBPS10A

New to SS&Si? Apply for a dealer account
Share
  • Fast shipping from four branches
  • 30-day returns on unopened products
Questions? Call us 866-364-0030The SS&Si dealer team

The MIRBPS10A Remote Booster Power Supply extends NAC power wherever the job needs it - no new panel run required. Drop it on an existing notification appliance circuit, wire up to four Class B (or two Class A) output circuits rated at 3 amps each, and let the built-in battery charger handle standby. UL 864 10th Edition listed for fire alarm, Mass Notification/Emergency Communication (MNEC), and life safety applications.

Built for the commercial fire installer

The BPS installs in indoor dry locations and cascades cleanly - existing NAC end-of-line resistors stay where they are, and multiple boosters can stack on a single circuit without special configuration. Dual-input activation circuits accept 6 to 45 VDC filtered or 11 to 33 VDC unfiltered, so it integrates with virtually any FACP on the market. The steel enclosure has room for up to two 10 Ah batteries internally, or pair it with an external battery cabinet for up to 65 Ah of standby. Agency listings include UL, ULC, CSFM, NYC Fire Dept., and FM Approved.

Key features

  • Four Class B NAC outputs (convertible to two Class A): 3A per circuit, 10A total capacity at 24 VDC
  • Built-in battery supervision and charging: supports 10 Ah internal or up to 65 Ah with external battery cabinet for extended standby
  • Genesis and Enhanced Integrity synchronization: keeps notification appliances in sync across the entire system
  • Multiple signal rates: continuous, 3-3-3 temporal, or follow the installed panel's coded NAC output
  • Self-restoring overcurrent protection on every output circuit - no fuse replacement after a fault
  • Seven on-board diagnostic LEDs: one per NAC fault, plus battery fault, ground fault, and AC power for fast troubleshooting
  • Optional OSHPD seismic pre-approval for component Importance Factor 1.5 installations

System requirements

Connects to any fire alarm control panel's NAC output or Kidde Commercial Signature Series control modules (CC1(S), CT1, CT2). The steel enclosure accepts 3/4-inch conduit and accommodates 18 to 12 AWG wiring. Internal mounting brackets support up to three Signature two-gang modules for addressable integration.

Specifications

SKUKD-MIRBPS10A
BrandKidde Commercial
Form factorWall-mount steel enclosure, 17.0 x 13.0 x 3.5 in (43.2 x 33.0 x 8.9 cm)
NAC output circuits4 Class B (convertible to 2 Class A), 3A max per circuit, 10A max total
NAC output voltage18.2 to 27.0 VDC
Power input120VAC or 220-240VAC, 50/60Hz, 580 watts
Auxiliary output4 configurable (19.1 to 27.0 VDC) plus 200 mA dedicated (19.5 to 27.0 VDC)
Input activation voltage6 to 45 VDC filtered-regulated, or 11 to 33 VDC full-wave rectified
Internal supervisory current70 mA + 35 mA per circuit set to AUX
Internal alarm current270 mA
Battery capacityUp to 10 Ah internal (2x 12V10A); up to 65 Ah with external battery cabinet
Output signal ratesContinuous, 3-3-3 temporal, or follow installed panel NAC
Notification appliance syncGenesis and Enhanced Integrity synchronization
Trouble relay2A @ 30 VDC
Ground fault detectionEnable or disable via jumper
Terminal wire gauge18 to 12 AWG
Conduit3/4-inch knockouts
Signature module mountingAccommodates up to 3 two-gang modules
NAC wiring stylesClass A or Class B
Operating temp32° to 120°F (0° to 49°C)
Operating humidity0 to 93% non-condensing @ 32°C
ComplianceUL 864 10th Edition, UL 636, UL 609, UL 365, UL 1076, UL 1610, ULC-S527, ULC-S303, C22.2 No. 205
Agency listingsUL, ULC, CSFM, NYC Fire Dept., FM Approved
Shipping weight15.05 lb (6.8 kg)

Documents and resources

FAQs

Can I cascade multiple boosters on one NAC circuit?
Yes. Existing NAC end-of-line resistors do not need to be installed at the booster's terminals. Multiple boosters can be driven from a single NAC circuit without special configuration.
Does this support Class A NAC wiring?
Yes. The four Class B output circuits are field-convertible to two Class A circuits.
What battery backup options are available?
The enclosure holds up to two 10-amp-hour batteries internally. For longer standby, pair it with an external battery cabinet (BC-1 or BC-2) for up to 65 amp-hours of backup capacity.
Can the NAC outputs be used for auxiliary power instead?
Yes. All four NAC outputs can be field-configured as auxiliary 24 VDC outputs (19.1 to 27.0 VDC). A dedicated 200 mA AUX output is always available. AUX circuits can auto-deactivate 30s after AC loss for door holder use.
What signal rates does the BPS support?
Continuous, 3-3-3 temporal, or follow the coded signal rate of the installed fire alarm control panel's NAC. This lets you match the main system or run independent signaling where needed.
Is this seismic rated?
Optional. Order the BPSEQ Seismic Kit for OSHPD seismic pre-approval at component Importance Factor 1.5. Anchorage to site structure may require local AHJ or structural engineer review.
All Kidde Commercial