• SS&Si
  • Kidde Commercial
  • Kidde | Genesis LED EGCS Series Ceiling Speaker-Strobe, 15-115cd Selectable, White, ALERT Marking | EGCSVWA
Genesis LED EGCS Series Ceiling Speaker-Strobe, 15-115cd Selectable, White, ALERT Marking
Kidde Commercial

Genesis LED EGCS Series Ceiling Speaker-Strobe, 15-115cd Selectable, White, ALERT Marking

SKU KD-EGCSVWA

New to SS&Si? Apply for a dealer account
Share
  • Fast shipping from four branches
  • 30-day returns on unopened products
Questions? Call us 866-364-0030The SS&Si dealer team

The Kidde Genesis LED EGCS ceiling speaker-strobe combines high-fidelity voice notification with field-selectable strobe output in a single low-profile device. At under two inches off the ceiling, it sits nearly flush on standard electrical boxes and keeps hallways and open ceilings looking clean while meeting NFPA 72 notification requirements.

Built for the commercial fire alarm installer

Speaker taps (1/4W, 1/2W, 1W, 2W) and voltage (25VRMS or 70VRMS) are both field-selectable via onboard switches, so one SKU covers a range of coverage zones without stocking multiple models. Strobe candela is also field-selectable at 15, 30, 75, or 115 cd. The unit draws a constant 35 mA on filtered DC regardless of candela setting, which simplifies NAC power budgeting on large loops.

Synchronization uses the same Kidde CC Series protocol and works with Kidde Signal Modules, Booster and Auxiliary Power Supplies, Intelligent and Conventional Control Panels. Genesis LED strobes are backwards compatible with legacy Xenon Genesis devices on the same NAC circuit, so you can upgrade a floor at a time without rewiring.

Key features

  • Field-selectable candela: 15, 30, 75, or 115 cd from a single SKU - no returns for wrong output
  • Field-selectable speaker: 25VRMS or 70VRMS operation with four wattage taps (1/4W, 1/2W, 1W, 2W)
  • Low-profile design: 6.8" diameter, under 2" depth - sits nearly flush on 2-gang and 4" square boxes
  • Constant current draw: 35 mA (DC) across all candela settings simplifies NAC circuit calculations
  • Room-side wiring plate included: install and wire without pulling the ceiling tile again
  • Backwards compatible: mixes with legacy Xenon Genesis strobes on the same synchronized circuit
  • Built-in DC blocking capacitor: enables electrical supervision of the audio distribution circuit

Mounting

Installs on 2-gang or 4-inch square electrical boxes (minimum 1-1/2" deep). Recommended mounting height is 81" AFF per NFPA 72. Wiring uses 12-18 AWG in-out screw terminals. The included GRSW room-side wiring plate allows termination without ceiling access after initial rough-in.

Specifications

SKUKD-EGCSVWA
BrandKidde Commercial
Form factorCeiling-mount speaker-strobe, round, low-profile
Power input16 to 33 VDC or 16 to 33 VFWR (strobe); 25VRMS or 70VRMS selectable (speaker)
Power consumption35 mA at 16-33 VDC (all candela settings); 45 mA at 16-33 VFWR
Light output15, 30, 75, or 115 cd (field selectable)
Speaker wattage1/4W, 1/2W, 1W, 2W (field selectable)
Speaker frequency response400 Hz to 4,000 Hz
Sound output87 dB reverberant at 2W; STI 0.81
Strobe flash rate1 fps (flash per second) approx.
Synchronization20 ohm max. between any two devices; Kidde CC Series protocol
Compatible sync sourcesKidde CC Series Signal Modules, Booster and Auxiliary Power Supplies, Intelligent and Conventional Control Panels
Wire size12 to 18 AWG (0.75 to 2.50 mm²)
Dimensions6.8 x 1.82 in (17.27 x 4.62 cm) diameter x depth
Strobe-to-box center offset-1.70 in (-4.32 cm)
Trim platesEGCTR, EGCTW 10.6 x 0.3 in (26.92 x 0.76 cm)
Mounting2-gang and 4-inch square electrical boxes (min. 1-1/2" deep)
Operating temp32 to 122°F (0 to 50°C)
Operating humidity0 to 93% noncondensing
Storage temp-40 to 158°F (-40 to 70°C)
ColorWhite (RAL 9002)
MarkingALERT
ComplianceUL listed (S218, S5389), FCC (7320-1657:0516), FM Approved
Low frequency capableYes, 520 Hz tone support

Documents and resources

FAQs

What electrical boxes does this mount on?
Standard 2-gang and 4-inch square electrical boxes with a minimum depth of 1-1/2 inches (3.81 cm). Recommended mounting at 81 inches AFF per NFPA 72.
Can I mix this with older Xenon Genesis strobes on the same circuit?
Yes. Genesis LED devices are backwards compatible with legacy Xenon Genesis strobes on the same synchronized NAC circuit. You can upgrade a building floor-by-floor without rewiring existing loops.
How do I change the candela or speaker tap in the field?
Candela (15, 30, 75, or 115 cd) and speaker wattage (1/4W, 1/2W, 1W, 2W) are set via onboard selector switches accessible from the front of the device. Speaker voltage (25VRMS or 70VRMS) is also switch-selectable. No special tools required.
Does the strobe current change when I select a higher candela?
No. The Genesis LED EGCS draws a constant 35 mA on filtered DC regardless of the candela setting (15, 30, 75, or 115 cd). This simplifies NAC power budgeting across large notification circuits.
What panels and sync modules does this work with?
Synchronizes with Kidde CC Series Signal Modules, Booster and Auxiliary Power Supplies, and both Intelligent and Conventional Kidde Control Panels. 20 ohm max wire resistance between any two devices on the loop.
Is the room-side wiring plate included?
Yes. The GRSW room-side wiring plate is included with this model (EGCSVWA). It allows wiring terminations from the room side without pulling the ceiling tile after initial rough-in.
All Kidde Commercial