• SS&Si
  • Kidde Commercial
  • Kidde | Genesis LED EG1 Series Wall-Mount Chime-Strobe, Selectable 15/30/75 cd, Red, FIRE Marking, 24 VDC | EG1RF-CVM
Genesis LED EG1 Series Wall-Mount Chime-Strobe, Selectable 15/30/75 cd, Red, FIRE Marking, 24 VDC
Kidde Commercial

Genesis LED EG1 Series Wall-Mount Chime-Strobe, Selectable 15/30/75 cd, Red, FIRE Marking, 24 VDC

SKU KD-EG1RF-CVM

New to SS&Si? Apply for a dealer account
Share
  • Fast shipping from four branches
  • 30-day returns on unopened products
Questions? Call us 866-364-0030The SS&Si dealer team

The Kidde EG1RF-CVM is a Genesis LED EG1 Series wall-mount chime-strobe that combines audible chime notification with field-selectable LED strobe output in a compact single-gang form factor. High-efficiency LED optics deliver significant current savings over legacy Xenon strobes, reducing the number of NAC circuits and power supplies on the job while maintaining full backward compatibility with existing Xenon devices on the same circuit.

Built for the commercial installer

The EG1 platform mounts to any standard 1-gang electrical box with no trim ring required. Optional EG1TR trim rings cover 4-inch square and oversized openings when needed. The device protrudes about 1" from the mounting surface with no visible screws, and under-cover diagnostic test points let you validate the NAC and verify device function without removing the unit from the wall. Slide switches handle all field configuration - candela selection, tone pattern - without tools.

Listed to UL 1971, UL 1638, and UL 464 with CSFM approval. ADA compliant per CFR Chapter 28 Part 36. Red housing with FIRE marking.

Key features

  • Field-selectable strobe output: 15, 30, or 75 cd - change under the cover without removing the device from the wall
  • Ultra-low current draw: LED technology reduces circuit loading, often allowing smaller wire gauge and fewer power supplies than Xenon equivalents
  • Single-gang footprint: compact 3 x 4-5/8 x 1-1/8 in. profile fits tight spaces and mounts flush
  • Backward compatible: mix freely on the same NAC circuit and field of view as legacy Xenon-based Genesis strobes
  • Quick-swap covers: change housing color or marking in the field without replacing the appliance
  • Synchronized flashing: exceeds UL synchronization requirements when paired with a compatible Kidde signal source

System requirements

Operates on a compatible Kidde NAC circuit at 16 to 33 VDC (or 16 to 33 VFWR). Strobe synchronization requires a Kidde CC Series signal module, booster power supply, auxiliary power supply, or compatible intelligent or conventional FACP. Wire with 12 to 18 AWG.

Specifications

SKUKD-EG1RF-CVM
BrandKidde Commercial
Form factorWall-mount chime-strobe, single-gang
Light outputSelectable 15, 30, or 75 cd
Flash rate1 fps (approx.)
Operating voltage16 to 33 VDC, 16 to 33 VFWR
Wire size12 to 18 AWG
Dimensions3 x 4-5/8 x 1-1/8 in. (7.62 x 11.75 x 2.86 cm)
Compatible electrical boxes1-gang, 2-gang, 4-inch octagon, 4-inch square (min. 1-1/2 in. deep)
Housing colorRed
Housing markingFIRE
Synchronization20 Ω max. between any two devices on the same NAC circuit
Sync sourcesKidde CC Series Signal Modules, Booster and Auxiliary Power Supplies, Intelligent and Conventional Control Panels
Agency listingsFCC, ICC, UL 1971, UL 1638, UL 464, CSFM
ComplianceADA (CFR Chapter 28 Part 36)
Operating temp32 to 122°F (0 to 50°C)
Operating humidity0 to 93% noncondensing

Documents and resources

FAQs

Does this mix with existing Xenon strobes on the same circuit?
Yes. Genesis LED EG1 strobes can share a NAC circuit and field of view with legacy Xenon-based Genesis devices. No need to replace existing devices to start deploying LED.
What electrical boxes does this fit?
Mounts to standard 1-gang, 2-gang, 4-inch octagon, or 4-inch square boxes at least 1-1/2 in. deep. Boxes wider than 3 inches require an optional EG1TR trim ring.
Can I change the candela setting after installation?
Yes. Remove the cover and slide the candela switch to 15, 30, or 75 cd. The device stays on the wall. The current setting is visible through a window on the left side when the cover is closed.
What synchronization source does this require?
Compatible with Kidde CC Series Signal Modules, Booster and Auxiliary Power Supplies, and both Intelligent and Conventional Fire Alarm Control Panels. Maximum 20 Ω between any two synchronized devices.
Is this ADA compliant?
Yes. Meets ADA requirements per CFR Chapter 28 Part 36 for visual and audible notification in commercial applications.
All Kidde Commercial