• SS&Si
  • Kidde Commercial
  • Kidde | Genesis LED EGC Series Ceiling Mount Mass Notification Strobe, Red, ALERT Marking, Amber Lens | GCVRA-A
Genesis LED EGC Series Ceiling Mount Mass Notification Strobe, Red, ALERT Marking, Amber Lens
Kidde Commercial

Genesis LED EGC Series Ceiling Mount Mass Notification Strobe, Red, ALERT Marking, Amber Lens

SKU KD-GCVRA-A

New to SS&Si? Apply for a dealer account
Share
  • Fast shipping from four branches
  • 30-day returns on unopened products
Questions? Call us 866-364-0030The SS&Si dealer team

The Kidde Genesis LED EGC Series GCVRA-A is a ceiling-mount mass notification strobe for commercial and institutional spaces where visual ALERT signaling is required alongside or separate from fire alarm notification. The amber lens and red ALERT-marked housing distinguish mass notification from fire alarm signaling, helping occupants differentiate between emergency types at a glance.

Built for the commercial installer

The EGC Series mounts to any standard 1-gang, 2-gang, 4-inch octagon, or 4-inch square electrical box using the included GP10 room side wiring plate. The universal wiring plate supports pre-installation and pre-wiring before the device arrives on site, and the included diagnostics check bar lets you verify continuity before snapping the unit into place. LED technology draws significantly less current than legacy Xenon strobes, allowing more devices per NAC circuit, longer wire runs, and fewer booster power supplies. UL 1971 listed. ULC-S526. FM Approved.

Key features

  • Mass notification visual signaling: amber lens with ALERT marking differentiates from fire alarm strobes on shared campuses and facilities
  • Field-selectable candela output: set to 15, 30, 75, or 115 cd via slide switch under the cover without removing the device from the ceiling
  • Ultra-low current draw: LED technology pulls just 35 mA (DC) or 45 mA (VFWR), fitting more devices per circuit and reducing booster requirements
  • Universal mounting: fits 1-gang, 2-gang, 4-inch octagon, and 4-inch square boxes with optional EGCTR/EGCTW trim plates for oversized openings
  • Backward compatible: mix with legacy Xenon Genesis strobes on the same NAC circuit for phased upgrades without full system replacement
  • Diagnostics port: under-cover test points for NAC circuit testing while mounted

System requirements

Operates on 16 to 33 VDC or 16 to 33 VFWR notification appliance circuits. Synchronizes with Kidde CC Series Signal Modules, Booster and Auxiliary Power Supplies, and Intelligent and Conventional Control Panels. Requires GP10 room side wiring plate (included). Electrical boxes must be at least 1-1/2 in. (3.81 cm) deep.

Specifications

SKUKD-GCVRA-A
BrandKidde Commercial
Form factorCeiling mount strobe, low-profile LED
Light outputField-selectable 15, 30, 75, or 115 cd
Lens colorAmber
Housing colorRed
Housing markingALERT
Operating voltage16 to 33 VDC, 16 to 33 VFWR
Current draw35 mA (16-33 VDC), 45 mA (16-33 VFWR)
Strobe flash rate1 fps (approx.)
Synchronization20 ohm max. between any two devices
Sync sourcesKidde CC Series Signal Modules, Booster and Auxiliary Power Supplies, Intelligent and Conventional Control Panels
Wire size12 to 18 AWG (0.75 to 2.50 mm2)
MountingCeiling mount
Compatible electrical boxes1-gang, 2-gang, 4-inch octagon, 4-inch square (min. 1-1/2 in. deep)
Dimensions6.8 x 1.82 in. (17.27 x 4.62 cm), diameter x depth
Profile depthApprox. 1.5 in. from mounting surface
Operating temp32 to 122°F (0 to 50°C)
Operating humidity0 to 93% noncondensing
Storage temp-40 to 158°F (-40 to 70°C)
ComplianceUL 1971, ULC-S526, CSFM, FM Approved, FCC
Trim platesEGCTR (red), EGCTW (white) - 10.6 x 0.3 in.
Wiring plateGP10 (included)

Documents and resources

FAQs

Does this strobe work on the same NAC circuit as existing Xenon Genesis strobes?
Yes. Genesis LED EGC strobes are backward compatible with legacy Xenon-based Genesis strobes. You can mix LED and Xenon devices on the same NAC circuit without modifications, making phased LED upgrades straightforward.
How do I change the candela setting?
Remove the cover and slide the candela switch to 15, 30, 75, or 115 cd. The device stays ceiling-mounted during the change. The selected setting is visible through a window after replacing the cover.
What makes this different from a standard fire alarm strobe?
The GCVRA-A has an amber lens and ALERT marking instead of the clear lens and FIRE marking on standard fire alarm strobes. This helps occupants differentiate mass notification alerts from fire alarms on shared campuses.
What electrical boxes are compatible?
Standard 1-gang, 2-gang, 4-inch octagon, and 4-inch square boxes. Boxes must be at least 1-1/2 inches (3.81 cm) deep. Optional EGCTR (red) or EGCTW (white) trim plates are available to cover oversized openings.
What synchronization sources work with this strobe?
Kidde CC Series Signal Modules, Booster and Auxiliary Power Supplies, and Intelligent and Conventional Control Panels. Sync keeps strobes within 10 ms over a two-hour period per UL requirements.
All Kidde Commercial